Oven Fault codes
AMANA CALORIC
Display -glass link ERC Condition Repair door flashing #0,1,2,3 latch switch broken replace lock flashing latch switch broken replace F 0 loss of safety signal replace adapter board F 1 watchdog circuit replace ERC F 2 oven too hot check sensor-1100 ohms F3 F4 open or shorted sensor replace sensor F7 shorted touch panel replace glass panel F9 motorized door check latch FF lock error check switch and motor ERC III / Relay board with separate board / push buttons F0 shorted push pad replace F1 failed ERC replace F2 oven too hot check sensor 1100 ohms F3 F4 shorted or open sensor replace F5,F6,F8 failed ERC replace F7 shorted or sticking button check glass alignment F9 door latch failure replace
GENERAL ELECTRIC HOTPOINT RCA
Display Condition Repair F0 and F1 Failed Thermister Control Replace ERC F2 Oven Temp Exceeds 590
w/unlocked doorHigh resistance or
interference in sensor
Likely a bad sensorF3 Open sensor circuit Bad sensor or
open sensor fuseF4 Shorted wire (sensor) Locate and Correct F7 A= Function pad button stuck
or
B= Bad clockUnstick Button
or
Replace ClockF8 Component failure Replace ERC F9 Program w/door circuit Check Wiring
FRIGIDAIRE TAPPAN GIBSON WESTINGHOUSE
Display Condition Repair F0 & F1 EOC failure Replace EOC (Electronic Oven Control / Clock) F2 Oven too hot Likely a bad sensor (should read 1100 ohms)
Possible bad EOC (Electronic Oven Control / Clock)F3 Oven Sensor Open Replace sensor F4 Oven Sensor Shorted Replace sensor F5 or F6 or F7 EOC failure Replace EOC (Electronic Oven Control / Clock)
WHIRLPOOL ROPER KITCHENAID
NOTE: Not valid for Y line. If there is a Y near the end of your model number, do not use this chart.
Display Condition Repair 4 Digit Display FO - E0 Analog to Digital
FailureDisconnect for 30
seconds- if display
re-appears- replace
controlF1 - E1 Safety flip flop Replace ERC (Electronic Range Control / Clock) F2 - E0 shorted keypad replace F3 - E0 sensor or sensor fuse opened replace sensor or fuse F3 - E1 sensor shorted replace sensor F3 - E2 oven too hot replace sensor F3 - E3 clean temp. too hot replace sensor F5 - E0
F5 - E1 and E2check door/latch
switchreplace 2 Digit Display F0 or F1 or F5 Failed transistor Replace ERC (Electronic Range Control / Clock) F2 Oven temp too high 1. Test operation of door lock on self-clean models.
2. Test relay contact operation
3. High resistance in sensor (should be apx. 1100 ohms)F3 Open sensor or thermal fuse Replace sensor or thermal fuse F4 Shorted sensor Replace sensor F6 Problem in time keeping circuit 1. Reset time and/or cooking operation
2. Check for proper groundF7 Stuck function switch or button on ERC Replace ERC (Electronic Range Control / Clock) F8 Failure of ERC Replace ERC (Electronic Range Control / Clock) F9 Door lock circuit Check wiring and test operation of door lock switch
MAYCOR MAYTAG MAGIC CHEF JENNAIR ADMIRAL
Display Condition Repair F1 Defective Touch Pad or Membrane Replace Touch Pad or Membrane. (I've seen this on several ranges if you are getting an F1 code I would recommend replacing the touchpad.) F1 watch dog on board bad touchpad or clock
see Clock Pad Test for procedureF2 oven too hot bad relay board (if present)
or bad sensorF3 or F4 open or shorted sensor replace sensor F5 hardware and watchdog
circuits disagreereplace clock F6 missing AC signal Check for proper voltage F7 function key shorted or stuck button replace touch pad or clock or unstick button F8 A/D supervisory replace clock F9 door latch supervisory check door lock circuit
or replace clockF0 function key stuck replace touch pad or clock
Thermador If an error code appears in the cook mode window
Your oven is equipped with an extremely reliable and accurate electronic control. On the rare occasion that something occurs that causes a malfunction, am error message will appear in the oven selector window.Some errors (E1, E9, E11, E12, and E13) must be cleared by turning off the oven at the circuit breaker and then turning it back on. When an error remains displayed steadily in the off position, after attempting to clear the error, a service call is required. Have the error code available when you call for service. This will help service determine the problem.
Error Code Notes Repair E1 C E Control board problem E2 K G Cook or clean mode runaway E3 A H Open oven sensor (over 5000 ohms) E4 A H Shorted sensor (under 500 ohms) E5 K D Control board too cold or too hot, or defective board. E6 C J Control board problem E7 A I Illegal temp. display turn off and retry E8 A D Control board problem E9 A E Latch switch problems E10 B D Control board problem E11 A F CT oven; latch switch problem E12 A E CT oven; latch switch problem E13 A C CT ovens; latch froze or no power to latch motor
CMT ovens; control board not convertedE14 A E Latch switch problem E15 B D Control board problem
Notes A Turns heat off on failed oven only, micro not affected B Turns all heat off, micro not affected C Disables clean mode in both ovens, allows cook and microwave D Error will remain in display until repaired and powered up. No error tones E Turning to off stops error and flashing can tweak away code F Tweaking clears to "---" for retry G Clears when oven temp drops below runaway temp and selector is off H Can be cancelled by tweaking if a good sensor is detected I Cleared with a mode change J Can be tweaked away for retry. User must unlatch and delete the "---" to try to relatch the door K Turns all heat and micro off L If two switches show locked door, then "E13" and "Lock" are permanent in display (all modes). If two switches show an open door you can tweak away the "E13"
